A Step-by-Step Overview to Installing a Bathtub
A Step-by-Step Overview to Installing a Bathtub
Blog Article
We've found this article relating to Installing A Bathtub directly below on the net and reckoned it made sense to talk about it with you over here.
Installing a bath tub isn't precisely brain surgery, however it does call for strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently accessible, the job can move immediately; if you have to open a wall to remove the old tub and also position the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub as well as embeded in the new one. Make certain you have actually qualified on your own for the work and fit trying it. Rather than employing a specialist to take control of a halfway-completed project, it is better to consider employing one before you begin. Opportunities are you might require a professional plumber to make tube links.
This article will assist you mount a brand-new bathtub in your restroom if you have actually currently bought a new bathtub and also do not need to alter the plan of your previous water system pipelines.
Your tools and material list need to comprise the following:
Getting ready for the Installment
To start with, the supporting frame supplied with the bath ought to be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be fairly bothersome as a result of the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a towel all set for the continuing to be water that will come from the pipes. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are useful in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the bath tub until the spirit level reads degree.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply and inspect all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the tub as well as likewise inspect the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub should wait until the bath tub has been utilized a minimum of when as this will settle it into its final placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location between the tap as well as the sink. Protect the faucet in position with the manufacturer offered backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet ports. The former type ought to be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing problems with dampness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and also fittings. They are sold in tubes and also cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that write up on A Step-by-Step Guide to Installing a Bathtub while doing a lookup on the search engines. If you liked our blog posting if you please make sure you remember to share it. Kudos for your time. Kindly check our blog back soon.
Book-Now
Report this page